Roofing dumpster rental in Burlington
Need a roll-off dumpster fast when the roofers pull off? We drop a 10- or 20-yard container, haul it away when you're done.
Roofing Tear-off Dumpster Sizing by Squares
How big a roll-off do you actually need for a 25-square tear-off in Burlington? Our standard 20-yard container is the right fit; it features a low-wall design for easier loading. For asphalt shingles, use this rule: one square equals roughly two-thirds of a cubic yard. Tonnage limits apply for Chittenden projects, so watch your heavy material pile.
15-Yard Roofing Dumpster
- Capacity: 15 cubic yards
- Fits: 15–20 squares of asphalt shingle
- Best for: Single-layer ranch and bungalow tear-offs
Our 10-yard can fits a tight driveway, managing shingle weight during a single haul for your roofing tear-off.
20-Yard Roofing Dumpster
- Capacity: 20 cubic yards
- Fits: 25–30 squares of asphalt shingle
- Best for: Most two-story residential tear-offs
The 20-Yard Container is our roofing workhorse—low side walls let crews ground-throw shingles without needing extra scaffolding.
30-Yard Roofing Dumpster
- Capacity: 30 cubic yards
- Fits: 35–45 squares of asphalt shingle
- Best for: Multi-layer tear-offs and small commercial roofs
The 30-yard bin keeps larger tear-offs moving by avoiding a second haul-out that would slow crew demobilization.
Asphalt Shingle Weight and Tonnage Planning
Most roofers know three-tab averages 250 pounds per square while architectural laminate runs closer to 400; a 25-square tear-off lands between three and five tons before underlayment. How does that route onto a single hooklift truck? The weight limit caps most 10-yard dumpsters well below five tons, so a roofing can is built low-walled to keep shingles inside the haul-out limit.
When you mix shingle debris with framing or sheathing offcuts, the contents change from roofing material to general c&d debris. We route these mixed loads to our construction service—using a specialized container—to ensure all waste is handled correctly.
Driveway Placement for Roofing Crew Workflow
We angle the swing-door end of each roll-off to match your eave, allowing crews to ground-throw shingles directly into the container. Before our driver drops the can onto your concrete in Burlington, he places wooden planks under the rollers to protect the driveway surface. We always use driveway boards to prevent scarring. For proper roof tear-off container sizing and asphalt shingle disposal best practices guide, keep a six-foot tarp perimeter for easier nail sweeps.
Drop angle
Rear door toward the roof line
Set the swing-door end facing your eave to ensure that walk-in loading and ground-throw share the same path for your crew.
Surface protection
Wooden planks under every roller
Loaded shingle weight can gouge concrete; driveway boards stay under the rear rollers for the full rental window.
Sweep zone
Six-foot tarp perimeter
Stage magnetic sweepers on the tarp side so nail cleanup runs in parallel with loading your heavy debris.
Tile, Slate, and Metal Roof Tear-off Containers
Concrete tile, natural slate, and standing-seam metal weigh two to four times what asphalt does per square: they punish a standard bin that was not built for the load. For these tear-offs, we route in a reinforced 30-yard container with a heavier floor plate; we cap the fill volume well below the visual rim so axle weight stays legal. We set these via lowboy for stability, as we do for our general construction debris service.
Same-day Pickup for Fast Roof Project Turnover
Tear-offs run tight; the roll-off shouldn’t hold things up. Dispatch coordinates a same-day haul-out around the crew’s demobilization window so the driveway clears for inspection or gutter reinstall before the homeowner steps back on site; Burlington crews cover Chittenden fast. We’ll swap the container free for the next job.